How To Turn Off Water To Toilet

How To Turn Off Water To Toilet – As with most plumbing fixtures, toilets come with a built-in shutoff valve. In most cases, the shut-off valve is located within the toilet’s primary water supply. The toilets feature this dedicated shut-off valve for convenience. It is often necessary to shut off the water supply to a toilet when making repairs and replacing components. Simple DIY repairs like fixing a flush handle that is swinging or replacing a flapper that is preventing the toilet from running require that you shut off the water supply to the toilet. Although most toilets have shut-off valves, some older models may not have these readily available. In this post from Stan’s Heating, Air and Plumbing blog, we’ll walk you through the process of turning off the water supply to your toilet.

To find your shut-off valve, follow the tubing that fills the water tank. The shutoff valve is usually shaped like a football and is attached to a pipe or hose attached to the bottom of your toilet tank. The other end of this pipe should be attached to the wall.

How To Turn Off Water To Toilet

How To Turn Off Water To Toilet

It is important to note that some older toilets do not have shut-off valves in the back. In this case, it is recommended to shut off the main water supply to the house or to carry out the wooden board method. With the wooden board method, slide a small piece of wood under the float lever inside the main tank to hold it in place. This wooden board should be fixed in such a way that its bottom rests on the bottom of the tank. With the wooden board method, the wood will hold the float lever up, and so that the tank will not refill after the flush.

How To Fix A Toilet Fill Valve

Once you have located the shutoff valve, you will want to turn the valve clockwise, turning off the water supply to the toilet. The shut-off valve shouldn’t be difficult to turn, so if you find you’re having some trouble, don’t force the valve if it doesn’t turn easily. If the water valve seems rusted or is very hard to turn, try using some WD-40 or similar lubricant to get it working. If that still doesn’t work, it will probably have to be replaced by a professional plumber like the team at Stan’s Heat, Air & Plumbing.

How To Turn Off Water To Toilet

When the water supply to the toilet is turned off, the water in the back tank should be emptied and not refilled while flushing. If the toilet is clogged, the water in the tank can be checked by lifting the float lever. This lever is usually attached to a hollow, sealed float that sits above the water in the tank. If water is still flowing during the clogged toilet test, more water will be added when you move this lever. If the water is still on, be sure to push the float lever back to the immediate position to prevent the tank from overflowing.

Once you’ve completed your repairs and you’re ready to turn the water back on, simply turn the shut-off valve counterclockwise, or remove the wooden block for an older toilet. If you are unable to resolve the issue you are having with your toilet, and need further assistance, contact the Stan’s Heating, Air & Plumbing team today. Our team of experienced plumbers in Austin will be happy to help. For both standard and emergency plumbing services in Austin, contact us online or by phone to schedule service today! You can spend time rebuilding old valves, but problems will reappear years from now. The best way to deal with worn valves is to replace them with modern quarter-turn ball valves. They rarely lock, leak or get damaged and best of all, they only take about an hour to install. Here’s how to apply them.

How To Turn Off Water To Toilet

How To Stop A Toilet From Overflowing

If you have an older home with galvanized pipe, we suggest hiring a plumber to do the switch out. It may seem simple enough to take off the old valve and install the new one. But if the pipe has corroded internally or the threads are corroded, this ‘simple’ plumbing job can turn into a plumbing nightmare. If you have PEX or plastic pipe installed in your home, these instructions do not apply.

Once you’ve identified the type of connection, purchase a quarter-turn shutoff ball valve to match the size of the incoming copper pipe and the size of the supply tube connection. If you’re replacing a sweat valve, you’ll need a torch, flux, solder, emery cloth, wire brush, and flame retardant cloth to shield the wall. This is also a good time to replace an old supply tube and a broken shield (wall trim plate). Sorry to burst your bubble, but you need to stop believing these 10 plumbing myths ASAP!

How To Turn Off Water To Toilet

Sweat stop valves do not have a hex flat where the copper tube enters through the wall. Replace a sweat valve with another sweat valve or compression valve.

How Does A Toilet Work

Check the part of the valve closest to the wall. Look for a hexagonal compression nut and matching hex flats on the valve body next to the compression nut. If the valve has a compression nut but no hex flat, look for the two flats on the sides of the valve body.

How To Turn Off Water To Toilet

Shut off the water at the main shut-off valve. If you have a gas water heater, turn the knob to the “Pilot” position. Turn off the circuit breaker for the electric water heater. Then open one faucet on the lowest level of your home and one on the upper level to drain the pipes. Then disconnect the supply tube from the shut-off valve. Replace valve.

Close the new valve. Then open the water-main shutoff valve and let the water run until all the air is out of the pipes. Then close the top and bottom taps. Check new valve for leaks. Turn the water heater gas valve back ‘on’ or flip the circuit breaker on the electric water heater.

How To Turn Off Water To Toilet

Why Won’t My Toilet Stop Running?

Hold the valve with pliers, loosen the packing nut and unscrew the entire valve stem. Look inside and remove the old washer if it is stuck to the seat. Removing the valve stem lets any remaining water out, making the sweating process easier. Before doing any torch work, make sure there is a fire extinguisher nearby and protect the wall with a fireproof cloth. Then remove the old valve and the rest of the solder.

To start, wrap flame protection cloth over the copper tubing and tape it to the wall. Adjust the torch to a smaller notch and aim it at the valve body. As the solder melts, twist and pull the valve from the copper tubing with a pair of pliers.

How To Turn Off Water To Toilet

Clean the tubing with emery cloth. If you are replacing a sweat valve with a compression valve, remove all solder traces before attaching the new escutcheon, nut, and sleeve. Otherwise, remove enough of the old solder to slide the new sweat valve over the tubing. Unscrew the stem and wire brush on the new quarter-turn valve and apply flux to the valve and copper tube.

Chromed Water Stop Shut Off Valve Basin Toilet Washing Machine 3/8 1/2 3/4 Inch

Put on a pair of leather gloves and take a damp cotton rag (the microfibre cloth will melt). With a flame protection cloth, heat the valve enough to draw in the solder. Heat the remaining solder with a torch until it melts. As the solder melts, wipe away excess solder with a damp cloth. Be sure to wear leather gloves to prevent steam burns.

How To Turn Off Water To Toilet

To remove a compression-style valve, grasp the valve body with an adjustable or open-end wrench, or slip-joint pliers. Grasp the compression nut with the other wrench and turn it clockwise to loosen it. Then pull the copper tubing off the valve.

Next, remove the old compression sleeve and nut. Grip the old sleeve with pliers, using minimal pressure to avoid distorting the copper tube. Then spin and pull it out of the tubing. If the sleeve is stuck, then saw and broke it.

How To Turn Off Water To Toilet

How To Flush Your Toilet When The Water Is Shut Off

To pop it off, cut through the middle of the sleeve at an angle using a hacksaw. Use short strokes to avoid cutting into the copper tube. Check your progress and stop cutting before you reach the copper.

Insert a flat-blade screwdriver into the cut and twist the screwdriver to pry off the sleeve. Slide out the old sleeve, old compression nut, and escutcheon (if you’re going to replace it).

How To Turn Off Water To Toilet

Slide the new escutcheon and compression nut onto the copper tube. Then, slide the new compression sleeve over the copper tubing. If the old sleeve left depression marks, locate the new sleeve slightly past the marks.

Different Types Of Water Shutoff Valves And How To Choose One

Insert the new valve and apply a very light coat of pipe dope to the compression sleeve. Next, screw the compression nut onto the valve until it is secure. Hold the valve in place with a wrench or pliers and tighten the nut one-half to three-quarters of a turn (follow the manufacturer’s strict instructions). Connect supply tube and test for leaks.

How To Turn Off Water To Toilet

Several companies manufacture quarter-turn push-fit ball-style shutoff valves that are installed

Similar Posts