How To Stop Your Toilet From Running

How To Stop Your Toilet From Running – Do you often hear noises from your toilet? Do you see water running from the bowl long after you flush? It’s called a flushing toilet and is a big cut on your water bill.

But fear not—fixing a leaking toilet is one of the easiest home repairs. We scoured the Internet and spoke with hardware expert Nathaniel Garber, owner of Garber Hardware, a family-owned hardware store in the West Village since 1884, for tips on how to fix a leaky toilet.

How To Stop Your Toilet From Running

How To Stop Your Toilet From Running

First, lift the cover of the tank and look inside. If the water level is unusually low and leaking from the rubber flap on the bottom, you will need to replace the flap, which can be purchased at any hardware store for $5 to $15. The constant flow of hard water and bacterial growth in the toilet tank can damage the valve so that it hardens and does not seat on the valve seat.

How To Unblock Your Toilet And What Not To Put Down It

Most toilets leak due to a malfunctioning flapper. However, if you find that the water level in the tank is high and is instead going into the overflow tube at the top, then you really need to replace the fill valve. This rarely happens, but it can also cause a toilet leak – if you want to learn how to replace a fill valve, check out these video tutorials here and here.

How To Stop Your Toilet From Running

However, most of the time it is a flutter problem. The first thing you need to do is find the water valve behind the toilet and turn it clockwise to shut off the water supply.

Then open the lid of the tank and flush the toilet so that the water finally drains out of the tank. Once the tank is empty, or if possible, reach over to the valve and disconnect its rubber grip from the overflow pipe pin.

How To Stop Your Toilet From Running

What Causes A Toilet Float To Stick?

Bring your old flapper to the nearest hardware store and ask an experienced employee to find a new flapper that matches your toilet model. Most flaps come in universal and adjustable sizes, but different brands sometimes have specific requirements.

Once you have a new valve, wipe any dirt or bacteria from the valve seat with a cloth to ensure a clean seat. Push the rubber grip of the damper over the plastic pin, line it up with the valve seat, and place the lift chain back on the flush lever, leaving about half an inch of slack in the line. Adjust the chain if necessary.

How To Stop Your Toilet From Running

Turn on the water valve behind the toilet again and let the tank fill with water. Allow water to fill to about an inch below the top of the overflow tube.

Quick Fix For Running Toilets — The Family Handyman

Now test your layout. Open the water valve again to let water flow into the tank and flush several times. Check that the valve moves up and down properly, especially after flushing, that it closes completely and prevents all water from escaping. If it works – congratulations! You just fixed a leaky toilet, saving money and water.

How To Stop Your Toilet From Running

If you want to see this process in action, check out this video tutorial on Jeff Patterson’s Home Repair Tutor channel: Flushing a toilet isn’t just noisy and annoying; This means you spend money on extra water and your utility bills can go up. Fortunately, there are some simple solutions that can often solve the problem without requiring a plumber. Here’s how to identify the problem, troubleshoot your flushing toilet, and implement solutions.

There are three main problems that are often the cause of toilet leaks. You will need to examine each of these factors to determine what is causing the problem.

How To Stop Your Toilet From Running

How To Fix A Toilet That Won’t Flush

One of the most common causes of toilet flushing is a flapper that creates a seal at the bottom of your toilet tank and then allows water to flow into the bowl when you flush. The flapper can gradually wear and leak, at which point it must be replaced.

Duane Miller, owner of Stellar Plumbing, explains that there is an easy way to check if your valve is leaking water into the toilet bowl. You can add a few drops of food coloring to the toilet tank and then wait for 30 minutes. Do not flush the toilet at this time. After 30 minutes, check the toilet bowl to see if colored water has seeped into the bowl. If so, it means you need to replace the valve.

How To Stop Your Toilet From Running

According to Miller, if your float ball isn’t working or the height needs to be adjusted, your toilet may be constantly running water. Miller says that if your float isn’t set correctly, it can cause the water level in your tank to get too high.

How To Deal With A Slow Running Toilet

When the water gets too high, it can seep through the upper tank and into your overflow pipe. Your overflow pipe directs water into the toilet bowl so it doesn’t overflow the tank. As a result, the tube will continue to drain water into the bowl and your toilet will continue to flush to try to keep the water level very high.

How To Stop Your Toilet From Running

It is also possible that your fill valve is leaking and needs to be replaced. Your fill valve controls the flow of water into your tank and stays on until the tank is full. Sometimes it is also called a ball.

To check if your fill valve is working normally, remove the tank lid and flush the toilet. Check if water is leaking from any part of the valve. If you see no visible leaks, raise the arm attached to the float while filling the tank. The water should stop. If not, there’s probably a leak below the fill valve that you can’t see.

How To Stop Your Toilet From Running

Reasons Your Toilet Isn’t Working (and How To Fix Them)

The valve is at the base of the tank and allows water to flow from the tank to the bowl. Jim Still-Paper/Getty Images

If you find that the valve is leaking, you will need to replace it. This is a fairly simple process.

How To Stop Your Toilet From Running

1. Turn off the water supply. Your toilet is supplied with water through a hose, which is usually on the left side of the toilet. This hose goes to your wall or floor and will have a handle at the base of the hose. Turn the handle clockwise until it is tight.

Common Toilet Problems & How To Fix Them

2. Flush the toilet. Flush the toilet to remove any remaining water from the tank.

How To Stop Your Toilet From Running

3. Remove the flap. The flapper will have a chain that connects to a flush lever inside your tank that you can unclip. Different flaps are mounted in the tank in different ways, but you can move, bend, and otherwise remove the flap from the base of the tank.

4. Buy a new damper. Your new damper should be the same size and type as your old one. The easiest way to make sure you’re buying the right damper is to take an old damper with you to the hardware store so you can compare models. Many hardware store employees will also be able to help you.

How To Stop Your Toilet From Running

How To Flush The Toilet When The Water Is Off

5. Install the new damper. The exact installation method you use will depend on the type of damper you have, so follow the instructions that came with your new damper.

6. Adjust the flapper chain. The clapper chain must be the correct length. If it’s too long, the flapper won’t lift completely through the drain hole, so you won’t get a full flush. If it is too short, the flap will not be able to close and seal properly. Adjust the chain so that there is about ½ inch of slack when the flush lever is in the normal position.

How To Stop Your Toilet From Running

If your toilet is running because of your float, you may need to adjust it. There are two main types of floats. Ball and arm floats consist of a small plastic ball that floats on water. There are also column floats that install vertically in your toilet. The steps you follow will depend on the type of float you have.

How To Adjust Water Level In A Toilet Bowl

1. Check the float level. It is best to set the float one to two inches below the overflow tube. There may be a line on the toilet tank that identifies the ideal water line. Refer to this point so you know where you want your float to sit after adjustment.

How To Stop Your Toilet From Running

2. Turn off the water supply. Your toilet is supplied with water through a hose, which is usually on the left side of the toilet. This hose goes to your wall or floor and will have a handle at the base of the hose. Turn the handle clockwise until it is tight.

3. Release the float. Use a screwdriver to loosen the screws holding the float by turning it counterclockwise. The screws are often located near the fill valve.

How To Stop Your Toilet From Running

How To Reduce The Water Usage Of Any Toilet

4. Set the float. By looking at the water line on the tank, determine where the float needs to sit. You can loosen the screws to decrease the float or tighten them to increase the float.

5. Test the float level. After making the settings, turn on the water in the tank again by turning the handle on the water supply hose

How To Stop Your Toilet From Running

Similar Posts