How To Stop Your Toilet From Constantly Running

How To Stop Your Toilet From Constantly Running – Get a stronger flush – and a lower water bill. Find out how to fix the problem if your toilet keeps running.

Introduction Learn a simple four-step strategy that solves 95 percent of toilet flushing problems. Stop the water from flowing continuously, give it a quick boost and solve other common problems quickly and easily.

How To Stop Your Toilet From Constantly Running

How To Stop Your Toilet From Constantly Running

The basics of how toilets work haven’t changed much in the last 80 years. After a flush, water fills the tank and raises a float which shuts off the water when it reaches a certain level. The lever still opens the valve to cause a flush and it falls back into place as the water level drops.

Why Does My Toilet Keep Running?

So it’s no surprise that we still have to deal with the same common coil problems all the time. Sometimes the flush isn’t strong enough, sometimes the toilet keeps running, and sometimes the bowl doesn’t get refilled.

How To Stop Your Toilet From Constantly Running

The good news is that most of these problems are easy to fix, without having to replace the toilet. You can complete the first three steps in five minutes. This solves most of the problems. The fourth step is usually easy too, but not always. More on this later. These steps work for most toilets but not for pressure relief models. Here’s what to do if your toilet won’t stop working.

For toilet drain problems, remove the tank cap and locate the fill pipe. This is a small flexible tube that extends from the fill valve to the overflow pipe of the toilet. While the tank is filling, it sprays enough water down the toilet’s overflow pipe to refill the bowl after flushing is complete. If this pipe falls or a stream misses the overflow pipe, the bowl will not fill and your next flush will be sloppy (i.e., will not produce a strong siphon).

How To Stop Your Toilet From Constantly Running

Why Does My Toilet Keep Clogging?

Replace the fill tube and press it firmly against the fill valve. Make sure it ends about 1 inch above the rim of the overflow pipe and the fill pipe delivers water to the toilet overflow pipe. Flush the toilet and watch the water flow to make sure it goes down the toilet’s overflow pipe.

The water level in the tank is controlled by an adjustable float. A float that is set too low results in a weak color; if it is set too high, water flows into the toilet overflow pipe and the fill valve does not shut off. The toilets keep running. To learn how to fix a toilet that won’t flush, look for a level mark on the inside back of the tank and mark it on the toilet’s overflow pipe so you can see it more easily. If you can’t find one, measure about 1 inch on the overflow pipe and make a mark.

How To Stop Your Toilet From Constantly Running

Then flush the toilet and see if the water reaches and stops at that mark. If it doesn’t and the toilet keeps running, adjust the toilet tank float up or down. If you have an older toilet, you will need to bend the brass rod that connects to the float ball to make the adjustment. But with newer toilets, you usually screw or slide a clip along the rod. Flush the toilet after each adjustment. Continue adjusting the float until the water is off at the correct level.

Common Toilet Problems You Can Easily Fix

Also, make sure the water level is at least one inch below the C-L (critical level) marked on the fill valve. You can adjust the height of many valves to raise or lower C-L. Sometimes the fill valve won’t shut off, which means it’s broken. If so, turn off the water supply on the cover under the tank. Purchase a replacement valve. You don’t have to match the old one; many, as shown, fit most toilets. There is a change in 15 minutes.

How To Stop Your Toilet From Constantly Running

A chain that is too short or tangled will not allow the valve to close and water will continue to leak into the bowl. This causes the fill valve to turn on and off to fill the tank. Too long a chain, or a flush rod hitting the tank cap, will not open the valve wide enough to fully open the flush. You must hold the lever to complete a good flush.

To avoid lack of water in the toilet and other problems, adjust the link in the chain so that it is slightly slack when the valve is closed. Trim the excess chain at the bar so that there is only an extra inch left to reduce the risk of tangling. Then put the tank lid back on and make sure the flush rod doesn’t hit the lid when you push the lever. If it does, bend it slightly and reset the chain.

How To Stop Your Toilet From Constantly Running

Common Causes Of A Leaky Toilet (and How To Fix Them)

If you’ve completed the first three steps and your toilet continues to flush, you likely have a worn valve. To learn how to stop a toilet from overflowing, turn off the water, remove the old valve, and take it to a shop for a proper replacement. (Hardware stores often have a large selection.) Most caps fit over the overflow pipe ears. Others have a ring that slides over the tube.

Now here’s the catch. You may not find the right match. The range of flap styles has increased over the past 15 years, and you can find 15 to 20 flap options on store shelves. Some packages contain specific make and model information (so make a note of yours before you leave the house). Others have a “universal cover” label. If you can’t find a suitable replacement, try the nearest one and also take the universal type. They’re cheap, and the extra might save you a second trip to the store! (Avoid the “customizable” types unless you’re switching to an adjustable one.)

How To Stop Your Toilet From Constantly Running

Install the new cover and make sure it opens and closes freely. Then test it. If the toilet keeps running or intermittently, you’re not getting a good seal. Try a different valve if the toilet won’t stop flushing.

How To Stop A Toilet That Keeps Running

If you can’t find a valve that closes, consider replacing the entire toilet overflow pipe/valve. In most (two-section) toilets, this means removing the tank. It’s not difficult and doesn’t require any special tools. It takes about an hour and you avoid calling in an expensive plumber’s service.

How To Stop Your Toilet From Constantly Running

We are no longer supporting IE (Internet Explorer) as we work to provide a website experience for browsers that supports new web standards and security practices. iOS 17 Hands-On: Standby Modes, Stickers, and More How Your Sunglasses Affect Your Eye HealthAspartame, Diet Soda Cancer RiskSleep Bank: Everything You Need To KnowCompare Current Mortgage RatesPost-Prime Day DealsHyundai Ioniq 5 N Coupons

Our award-winning staff of experts selects the products we cover and thoroughly researches and tests our best selection. If you buy through our links, we may receive a commission. Review the ethics statement

How To Stop Your Toilet From Constantly Running

How To Fix A Running Toilet In 5 Simple Steps

Does your toilet flush all the time or at odd times? Here’s how to troubleshoot. Brian Bennett/

Sometimes the toilet works. A common problem your trusty tron ​​can develop with is that it always works. This constant flow of water is a noisy distraction – and it’s also a waste of money you’ll be paying on your next electricity bill.

How To Stop Your Toilet From Constantly Running

Fortunately, this is usually a fairly simple problem to fix. In this guide, I’ll outline the most likely reasons why the toilet keeps running, and I’ll also describe the first steps you should take to troubleshoot and resolve the issue. Once you get the hang of it, you’ll not only save money, but you’ll gain the skills to handle running toilets whenever and wherever you find them.

What To Do If Your Toilet Keeps Running

The first step is to turn off your toilet water supply. Most often, it’s a small knob on the wall to the right of the toilet that’s near the floor. Turn the knob all the way to the right (clockwise) to close the valve and pinch off the water supply. Doing otherwise will revive the water.

How To Stop Your Toilet From Constantly Running

Carefully remove the ceramic cap from the top of the water tank. It is fragile, so be sure to gently lower it to a safe resting place such as a bath towel. Take a look now. Inside the tank you will see all the main parts responsible for your toilet water control. These are flush valve, fill valve and fill tube.

Here is a view of the toilet water control system. On the left is the fill valve. On the right is the fill pipe, shutoff, and flush valve. Brian Bennett/

How To Stop Your Toilet From Constantly Running

What To Do If The Toilet Is Leaking At The Base

The fill pipe is a hollow plastic cylinder that is mounted vertically on the tank floor. One end of the tube is placed above the tank waterline. At the other end of the fill tube at the bottom of the tank is a cap, a rubber or silicone seal around the drain that lifts up each time you flush.

The purpose of the fill pipe is to receive water from the fill valve to refill the water tank after each flush of the toilet. It also acts as an overflow pipe to prevent water from overflowing the tank.

How To Stop Your Toilet From Constantly Running

As the water level in the tank drops, so does the float refill

Life Skill: How To Fix A Running Toilet

Similar Posts