How To Stop Toilet From Running

How To Stop Toilet From Running – When the toilet is constantly running, you may waste gallons of water and run up a higher water bill. Don’t worry, a working toilet is usually an easy fix. The three most common causes are a broken or dirty flange, a chain that is too long or too short between the spool arm and the flange, or a float that is out of position.

The first thing you need to do is turn off the water supply to the toilet. Find the silver button on the back of the wall behind the toilet and turn it to the right. Second, take the lid off the tank and start identifying all the components and how they work together.

How To Stop Toilet From Running

How To Stop Toilet From Running

First, make sure that the chain correctly connects the spool lever and the rubber latch. Sometimes the circuit is disconnected. Then shake the spool lever and check for too little or too much slack in the chain. If it is too short, water will continue to flow into the bowl because the valve is not sealed. If it is too long, the chain will not open the valve when the lever is pressed. If necessary, cut off the excess chain. The chain may also have a float attached, adjust the float so it is above the surface of the water.

My Toilet Is Leaking Or Is Runn

Over time, the valve may not close the drain because it has become dirty, deformed, or broken. If you need to clean or replace it, first empty the tank completely and then disconnect it from the circuit. The store will have several exchange options. If you can, match the brand or find a “universal” label that looks close to what you have. After reattaching the flange, test it with water to see if it seals properly.

How To Stop Toilet From Running

If you find that the flush valve (which holds the flange in place) may be the cause of the water leak and needs to be replaced, read these step-by-step instructions.

The water level inside the tank is controlled by an adjustable float. If the float is set too low, it creates a weak coil. If it is set too high, water will flow into the overflow pipe and run continuously. Find the fill level mark on the back of the tank and mark it on the overflow tube so it is easy to see. If you can’t see the mark, measure down about 1 inch into the overflow pipe and mark it.

How To Stop Toilet From Running

How To Fix A Running Toilet You Don’t Need A Plumber

Then turn on the water and flush the toilet to see where the water level stops compared to the mark. If water overflows, the pump float is too high. Adjust the float up or down accordingly. In an older toilet, you may need to bend the copper rod that connects to the float. In newer toilets, you just need to turn the screw or slide the clip along the rod. Sometimes the fill valve (to which the float connects) will not actually shut off and may be faulty. In this case, you will need to purchase a replacement valve.

If your toilet keeps running and these solutions don’t solve the problem, call the professionals at Bailey Brothers Plumbing at 405-896-9988. Our experts will ensure that your toilet works quickly and correctly. Get a stronger rinse aid and a lower water bill. Learn how to fix things if the toilet keeps running.

How To Stop Toilet From Running

Each editorial product is independently selected, although we may be compensated or receive an affiliate commission if you purchase something through our links. Ratings and prices are accurate and in stock at time of publication.

How To Plunge A Clogged Toilet

Introduction Learn the simple four-step strategy that solves 95 percent of toilet flushing problems. Stops continuous water flow, improves redness and solves other common problems quickly and easily.

How To Stop Toilet From Running

The basics of how a toilet works haven’t changed much in the last 80+ years. After flushing, water fills the tank, which raises a float that shuts off the water when it reaches a certain level. The lever still opens the valve to activate the flush, and it falls back into place when the water level drops.

So it should come as no surprise that we still experience the same common flushing problems from time to time. Sometimes the flush isn’t strong enough, sometimes the toilet keeps running, and sometimes the bowl doesn’t fill.

How To Stop Toilet From Running

How To Fix A Constantly Running Dual Flush Toilet

The good news is that most of these problems are easy to fix without changing the toilet. You can complete the first three steps in five minutes. This will solve most problems. The fourth step is also usually easy, but not always. More on that later. These steps are suitable for most toilets, but not for pressure-assist models. Here’s what to do if the toilet won’t stop working.

If you have a problem with the toilet overflow pipe, remove the tank cover and locate the fill pipe. This is a small flexible tube that runs from the fill valve to the toilet overflow pipe. As the tank fills, this tube sprays enough water through the toilet overflow pipe to fill the bowl after the flush is complete. If this tube falls or the water stream misses the overflow tube, the bowl will not fill and the next flush will be dirty (that is, a strong siphon will not form).

How To Stop Toilet From Running

Reattach the filler tube and press it firmly onto the filler valve. Make sure it is about 1 inch above the edge of the overflow pipe and that the fill pipe is sending water into the toilet overflow pipe. Flush the toilet and observe the flow of water to make sure it flows through the toilet overflow pipe.

Best Toilet Fill Valves That Stop Running Toilets

The water level in the tank is controlled by an adjustable float. A float set too low produces a weak coil; if it is set too high, water will flow into the toilet overflow pipe and the fill valve will not close. The toilet keeps running. To learn how to fix a toilet that won’t flush, find the fill level mark inside the tank and mark it on the toilet overflow pipe so you can see it more easily. If you can’t find it, measure about 1 inch into the overflow pipe and mark it.

How To Stop Toilet From Running

Then flush the toilet and see if the water reaches this mark and stops there. If not and the toilet continues to run, adjust the toilet tank’s float up or down. If you have an old toilet, you will need to bend the brass rod that connects to the flush ball to make adjustments. But with newer toilets, you usually turn a screw or slide a clip along the rod. Flush the toilet after each adjustment. Continue to adjust the float until the water shuts off at the appropriate level.

Also make sure the water level is at least one inch below the C-L (critical level) marked on the fill valve. You can adjust the height of many valves to raise or lower the C-L. Sometimes the filler valve just won’t close, which means it’s broken. If so, turn off the water supply at the valve under the tank. Purchase a replacement valve. You don’t have to go with the guy; many, like the one shown, fit most toilets. It’s a 15 minute shift.

How To Stop Toilet From Running

How To Troubleshoot A Running Toilet

A chain that is too short or tangled will prevent the valve from closing and water will continue to flow into the bowl. This causes the fill valve to cycle on and off to fill the tank. A chain that is too long or a flush rod hitting the tank lid will not open the valve wide enough to stay open for the full flush period. You will need to hold the lever to complete a good flush.

To avoid low water in the toilet bowl and other problems, adjust the chain link so that there is only a small amount of slack left when the valve is closed. Clip the excess chain at the bar to leave only about an inch extra to reduce the chance of tangling. Then put the tank cover back on and make sure that the flush rod does not come into contact with the cover when you press the lever. If it is, tilt it slightly and adjust the chain.

How To Stop Toilet From Running

If you have completed the first three steps and your toilet continues to run, you may have a worn valve. To learn how to prevent an overflowing toilet, turn off the water, remove the old valve and take it to a store to find an exact replacement. (Hardware stores often carry a wide variety.) Most flanges snap over the knobs on the overflow tube. Others have a ring that slides over the tube.

How To Fix A Slow Draining Toilet: A Diy Guide

Now here’s the catch. You may not find an exact match. The range of fender styles has grown over the past 15 years, and you can find 15 to 20 fender variations on the store shelf. Some packages include specific make and model information (so check yours before you leave home). Others have the label “universal flapper”. If you can’t find an exact substitute, try the nearest one and take a

How To Stop Toilet From Running

Similar Posts